Renault Laguna II - Interiors - Electric Window Problems - Regulator Repairs - Page 47 - Renault Forums :: Independent Renault forum

LinkBack Thread Tools Display Modes
post #231 of 383 (permalink) Old 24th October 2008
andymelvin's Avatar
Join Date: Mar 2008
Posts: 31
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 0
Thanked 0 Times in 0 Posts
Well the window is now working perfectly now with no abnormal noises or movements ?
Currently in andymelvin's garage:
2003 Laguna 2.0 IDE Initiale
andymelvin is offline  
Sponsored Links
post #232 of 383 (permalink) Old 12th January 2009
bamm bamm's Avatar
Join Date: Feb 2008
Posts: 69
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 0
Thanked 0 Times in 0 Posts
Originally Posted by MIKE4369 View Post
To get the door card off
1. remove the 3 torkx screws 2 at the bottom of the door and 1 in the door pull handle recess (under a plastic cover)
2 CAREFULLY prise off the card (its held on with small plastic pop clips and an adhesive strip) using a flat tipped screwdriver, put something between it and the paintwork bit of card/rag
3 unclip the door opener cable plastic cover and take off the cable.
4 unplug the switches, remove the switches first that is if you have the mirror switch and bank of window switches on the winder mech, they simply prise off by using a small driver to push in the locating clips. Remove the door light .
With the door card off you may find the adhesive strip has stretched so what I did was put a little line of super glue in the groove and stick the strip down and cut off the excess
5 the window mech is held on with 5 nuts (2 on each arm and 1 on the regulator/motor plate.
To remove the glass I found it easier to take off the top rubber door trim and lower the glass down. The glass is held in place on 2 plastic holders with retaining clips with lugs that go through the glass, reach in and release them by plulling the tabs off the lugs that go through the glass. Push the glass towards the door off the lugs and you should then be able to take it out through the top of the door ( keep it safe).
Undo the 5 nuts, unplug the motor unit and take out the window mech.
Replace the window mech tighten the nuts plug in the motor and lower the glass in from the top. The mech may be in a sort of mid-way psiton (on mine anyway) push the holes in the glass onto the plastic holders and replace the clips in the groove on the lugs. Replace the door opener cable in its holder and snap on the cover, plug the door light into its hole feed the wires for the switches into their holes. Replace the cables through the holes
I will be taking both rear doors apart soon to grease the mechs before they give trouble so I'll take some pics for reference
You can get relacement mechs off e bay for 110 make sure you order the correct type, 6 pin or 2 pin, 6 pin ones are fitted to cars with the anti pinch facility. This will be obvious when you take the door card off.
6 pin types are part no. 82 00 000 937 near side and 82 00 000 938 drivers side MAKE SURE BEFORE ORDERING. If anyone has a driver's side mech with a 29 pin plug (if you have electric seats) there is a simple way of fitting a 6 pin type saving mega bucks, the motor unit is basic to all type its just the regulator that differs.
I can give a contact who can supply if needed. Be quick they are in short supply!!
Hope this helps

PS there is another thread one with pics and a similar one to the above (mine) in the forum somewhere I'm sure a moderator will point you in the right direction
thanks for this thread all, got the same problem with my 2.2 dci had a look at getting the door card off and like already said in this thread didn't want to break something getting it off.
my window won't work at all but before it went i had the squealing and then it wouldn't go down or up.

so thankyou all i'll wait for better weather first though before undergoing the job.
Currently in bamm bamm's garage:
2004 2.2dci hatchback in pearl black and rides a honda cbr1000rr in blue,black and silver
bamm bamm is offline  
post #233 of 383 (permalink) Old 21st January 2009
Junior Member
Join Date: Jun 2008
Posts: 29
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 0
Thanked 0 Times in 0 Posts
Got a bizarre window problem. Rear driver's side window started going down by itself while I was driving. Would move about a millimetre at a time, sometimes more. I managed to get it back up, but it started moving down by itself again.

I put it all the way up, then decided to remove the window fuses until a sunny day when I could take a look at it properly. Even with the fuses removed, the window would still move down by itself, and I could still control that one window with the switch.

Any ideas what the hell could be causing that?!
Currently in elyl's garage:
2004 Laguna II Privilege 2.2dCi
elyl is offline  
post #234 of 383 (permalink) Old 21st January 2009
Technical Supremo

Join Date: Feb 2007
Posts: 43,087
Nominated 18 Times in 69 Posts
Nominated TOTW/F/M Award(s): 28
Thanks: 377
Thanked 5,239 Times in 4,738 Posts
When the window creeps down can you hear the motor running. If its slipping down without the motor kicking in I would suspect the regulator mechanism to be duff.
Other wise it could a faulty switch or water getting in somehwere.
Currently in madnoel10's garage:
Ford C-max 1.6 Style
madnoel10 is offline  
post #235 of 383 (permalink) Old 21st January 2009
Diamond member
DeeBeeS's Avatar
Join Date: Jul 2006
Posts: 169
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 0
Thanked 0 Times in 0 Posts
Enquiry as to fitting new window regulator

I have a Laguna Sports Tourer 2 and am in the process of renewing my windows regulator on the front drivers side.

I have purchased a regulator on Ebay for my car which is miles cheaper than from the main stealers. Just a quick question at the bottom of the rails on both sides they have two plastic clips. On these clips there are two slide on fasteners, do these clips fit into the two holes situated at the bottom of the window?

I would presume they do but I just wanted to make sure. I have left the plastic glass protectors that were already in the window.

Thank you

Currently in DeeBeeS's garage:
2001 Renault Laguna Sports Tourer 16v 1600
DeeBeeS is offline  

electric , enquiry , fitting , interiors , laguna , problems , regulator , renault , repairs , window

Quick Reply

Register Now

In order to be able to post messages on the Renault Forums :: Independent Renault forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

  LinkBacks (?)
LinkBack to this Thread:
Posted By For Type Date
DELFI: This thread Refback 23rd May 2007 10:36 AM
Untitled document This thread Refback 20th May 2007 02:37 PM

Posting Rules  
You may not post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome