Renault Scenic 1 - How To Change A Seatbelt*With Pics* - Page 3 - Renault Forums :: Independent Renault forum

LinkBack Thread Tools Display Modes
post #11 of 19 (permalink) Old 13th April 2009
Posts: n/a
Later Don

In the meantime, Brucie is much more like it
Sponsored Links
post #12 of 19 (permalink) Old 13th April 2009
Veteran Member
Technical Supremo
Lagdti's Avatar
Join Date: Dec 2005
Posts: 40,429
Nominated 2 Times in 20 Posts
Nominated TOTW/F/M Award(s): 18
Thanks: 149
Thanked 1,103 Times in 942 Posts
Didn't they do well?.

Yes,very off topic.

I'll try and get some pics and a bit writing sorted out and post it up.I've got another one prepared for removing the top of the dashboard which I'll sort out too.It's difficult to see just how much more exciting my life can get!..

Note to self......must get out more.

I'd rather push my Alfa than drive a BMW....
Currently in Lagdti's garage:
2004 Saab 9-5 HOT Aero and a 2001 Audi A3 1.8 Turbo
Lagdti is offline  
post #13 of 19 (permalink) Old 14th April 2009 Thread Starter
Junior Member
Spannerdemon's Avatar
Join Date: Dec 2008
Posts: 22
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 0
Thanked 0 Times in 0 Posts
Sounds like an exciting life to me!!

Seat belt is grey, and if you DO have one, I'll work something out with you. Thanks again.
Currently in Spannerdemon's garage:
1999 Renault Scenic 2.0
Spannerdemon is offline  
post #14 of 19 (permalink) Old 15th April 2009
Veteran Member
Technical Supremo
Lagdti's Avatar
Join Date: Dec 2005
Posts: 40,429
Nominated 2 Times in 20 Posts
Nominated TOTW/F/M Award(s): 18
Thanks: 149
Thanked 1,103 Times in 942 Posts
Righty ho,just before I start,I'm afraid that the seatbelt in the one we are stripping at work is pretty much fubar'd,so you'll have to try and source another one Spannerdemon.Sorry about that,ours is pretty filthy and it won't clean up,also there a couple of areas of damage to the webbing so I wouldn't be happy for you to use it.

But anyway,here is 'How To Remove A Seatbelt On A Scenic'.

Firstly,I have cheated as the Scenic had a leather interior in it which we have removed and sold,this makes access to the belt much easier,and it also means I have already removed the lower bolt from the belt which is on to the seat.I think you have to remove a round plastic cover in the side trim of the seat(ours was already missing) and then undo the bolt behind it(either a 16 or 17mm,I can't remember which).The belt will then release from the seat.If you are removing the belt to reuse it,you need to pull the belt out and then tie a loose knot in it to stop it retracting fully.If it goes past a certain point you won't be able to release it and the belt is junk.

OK,so here we have the belt.....

....and here it is with a knot tied in it!.

You need to first remove the cover from the top bolt(I know it's already missing in the above pic,they are out of sync a little!).The cover just flicks of with the aid of a small flat blade screwdriver.You need to make sure that you catch it as it releases,otherwise it'll fly accross the inside of the car never to be seen again!.

Then it's just a case of using a 17mm spanner to undo the bolt.

Now you have to remove the top door post trim to be able to remove the lower one and access the belt it's self.To remove the top trim you need to pop off the height adjust knob(it just literally pulls off,you may need to pursue it a little from behind with a screwdriver although you need to lever it away equally top and bottom/side to side otherwise you could snap the clip that holds it on).......

The top of the trim just pulls away from the top,it's clipped in so will again need a small bit of persusion from behind).

.....and then you need to lift the trim to release the fingers that hold it to the lower trim......

Once the top trim is off,it will expose the T20 headed screw holding the lower trim in place.....

.....which you need to undo.......

This will release the trim at the top,you then need to lift this trim in the same way as you did the top one to release the fingers holding it behind the lower sill trim......

(This ones taken at a bit of an odd angle,but I've tried to show the three fingers holding the trim on at the bottom)

You can then release the trim by feeding the belt through the split where the T20 screw was holding it in place.....

This will then expose the business end of the belt,the reel.This again is held in place with a 17mm bolt,this is slightly awkward to access unless you release the inner sill trim.This is quite a bit of extra work,so it's easier to just gently pull the trim back out of the way to access the bolt......

Once that bolt is removed,the belt can be removed and thats the job half done.

When fitting a replacement belt,make sure that the tab by the reel bolt fits into the hole in the door post.This is there to hold the belt at the right angle so it can be released......

Hopefully it'll be clearer when you have a go yourself.

When you remove the seat belt,unless you hold the reel at the right angle you won't be able to pull any belt off it as the locking mechanism will activate.Don't panic or try and force the belt out,just hold the real straight up and down as it would be when mounted in the car and it will eventually release.If you don't tie a knot in it when you remove the top bolt,the spring will retract all of the slack belt and it has happened to me where the whole belt has retracted and then you can't get any slack back in to it to release it..

Just take your time when doing the job,check everything twice and I'm sure you'll be OK.I know I don't have to say this,but a seatbelt could save your life so make sure your happy to carry the job out,and if not let a proffessional help out.Once you've got the belt fitted,make sure the belt pulls out and retracts properly,and also sit in the seat with the belt on and give the belt a hard,quick tug with your hand.You should feel it lock,this is what stops you flying fowards when braking hard or when your involved in an accident.

Any problems,let us know and we'll do our best to help out.

I'd rather push my Alfa than drive a BMW....
Currently in Lagdti's garage:
2004 Saab 9-5 HOT Aero and a 2001 Audi A3 1.8 Turbo

Last edited by Lagdti; 15th April 2009 at 10:07 PM.
Lagdti is offline  
The Following User Says Thank You to Lagdti For This Useful Post:
Dobert (14th January 2014)
post #15 of 19 (permalink) Old 15th April 2009
Platinum member
planmeca's Avatar
Join Date: Feb 2007
Posts: 2,448
Nominated 0 Times in 3 Posts
Nominated TOTW/F/M Award(s): 1
Thanks: 332
Thanked 323 Times in 277 Posts
Good post so far lag but do you need to use Snapon or will inferior spanners do just as well
Currently in planmeca's garage:
Renault Laguna 1.8 16v x 2 and a lot of other things. could really do with a tidy up to be honest I'll do it tomorrow
planmeca is offline  

belt , change , pics , removal , renault , scenic , seat , seatbeltwith

Quick Reply

Register Now

In order to be able to post messages on the Renault Forums :: Independent Renault forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Posting Rules  
You may not post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome