MEGANE II - bonnet won't open, solution - Page 3 - Renault Forums :: Independent Renault forum

Bodywork Paint care, corrossion, body kits, spoilers, skirts etc.

LinkBack Thread Tools Display Modes
post #11 of 12 (permalink) Old 11th September 2014
Diamond member
ste2425's Avatar
Join Date: Oct 2012
Posts: 349
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 30
Thanked 40 Times in 39 Posts
Re: MEGANE II - bonnet won't open, solution

Haven't suffered from this issue, but will be applying the zip ties anyway to ensure i don't in the future. (Taking gearbox out tomorrow so knowing my luck ill knock it )
Currently in ste2425's garage:
2003 Ford Ka 1.3 : 2003 Renault Megane 1.4 16v (RIP) : 1997 Fiat Cinquecento S (RIP) : 2000 Vauxhall Corsa (RIP) : 1997 Citroen Xsara 1.4 (RIP)
ste2425 is offline  
Sponsored Links
post #12 of 12 (permalink) Old 23rd April 2015
Junior Member
Join Date: Apr 2015
Posts: 1
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 0
Thanked 0 Times in 0 Posts
Thumbs up Re: MEGANE II - bonnet won't open, solution

Originally Posted by Aussiemike View Post
Took my 2006 Megane II (2006) CC in for an auto gearbox repair, when collected the bonnet release handle inside the car was functioning but there was no resistance to the cable and obviously not popping the bonnet. Took car to Renault dealership - they had never experienced this before and stated it would be a half day job at least to put right. At their prices I decided to have a go myself - Haynes manual to locate the bonnet mechanism and cable connection positions and then I started.
There are two cables that operate the bonnet release - from the handle inside the car this one terminates about level with the nearside headlamp/battery position and has a nipple connector. The bonnet release mechanism cable is about 2 feet long and has a cup shaped end to it that accepts the nipple end of the other cable. Both ends are housed in a plastic box attached to the slam panel directly opposite the battery. Inside this box the two cables connect to each other. What happened in my case was the short bonnet release cable had been pushed downward when the mechanics were working on the car - this separated the two halves of the plastic box and disconnected the cable joint. It is extremely easy to do this and I recommend all owners undertake a similar preventative measure that I explain later.
To get to this cable there are two methods - raise the front of the vehicle, remove all the under side plastic trays and access the cable by reaching up into the engine bay - the second method which I used was to remove the nearside front black plastic grill by the headlamp - get your fingers under the bottom edge starting at the headlamp and pull upward, the plastic grill separates from the bumper and as you move along it's length it will release without damage. Get a good torch and shine it in - you will see a grey plastic grill up top of the radiator by the bonnet - pull that free, mine came away with minimal damage and I can't actually see what function it served anyway. Reach your hand palm up between the top of the rad and the bonnet and move backward into the recess until your fingers feel the plastic cable sleeve which runs underneath the slam panel. Get a grip of this and start to free it downward as you also pull it back towards you - it should release easily and the U shaped cup end of this cable will appear - pull this cup and the bonnet opens. - From inside the engine compartment reconnect the two cables carefully reassembling the plastic box that houses that connection - I then drilled two holes alongside the box and using cable ties I ensured the box will not inadvertently come apart again. Hope this helps some one else - I do have photographs but the site won't let me post them for some reason - I don't have a security token??
Thanks Aussiemike,

Took my Renault Megane to the dealership and they were quite pricey. Don't know what
additional costs there would have been after they managed to open the bonnet in order to fix whatever they deemed wrong. I followed your instructions and to my delight I opened the bonnet. I also reassembled it using your cable tie idea.

Thanks mate!!!
RioSA is offline  

bonnet , megane , open , solution

Quick Reply

Register Now

In order to be able to post messages on the Renault Forums :: Independent Renault forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome