How to change front discs and pads(with pics) - Page 9 - Renault Forums :: Independent Renault forum

Brakes/Hubs Brakes, Hubs, and etc

LinkBack Thread Tools Display Modes
post #41 of 83 (permalink) Old 22nd August 2010
Junior Member
Join Date: Aug 2009
Posts: 4
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 0
Thanked 0 Times in 0 Posts
Re: How to change front brake discs and pads

Originally Posted by Lagdti View Post
Here is a 'how to' on replacing front brake discs and pads.

I did this on my Laguna 1 phase 2,but the basic principles are the same no matter what car your carrying this out on.

The first thing to do is remove the cap from the brake fluid reservoir.This will save you spraying brake fluid everywhere or damaging the master cylinder.Also,make sure the keys are in the ignition,but with the ignition off.If your car has ABS the pump could be damaged if you have the ignition switched on.

Next,remove the front wheels and put the car on axle stands.Work on one side of the car at a time,and turn the steering to gain easy access to the caliper.

Next,remove the lower caliper bolt.

To do this you will need a 13mm spanner on the bolt and thin headed 17mm open ended spanner to stop the inner slider from spinning.If you haven't got a thin 17mm spanner,then it is possible to use long nose pliers or molegrips.

Once this bolt is removed,pull the caliper up and then slide it off of the top slider.

It's a good idea to support the weight of the caliper by either tying it up to the suspension leg or resting it on top of something so as not to damage the flexible brake hose.

Next,remove the two brake pads......

Next,remove the two 18mm caliper carrier bolts.They will be reasonably tight.....

Once the carrier has been removed,the two disc holding bolts will need to be removed.It is best to hit the heads of them with a hammer before trying to remove them as they are T40 torx bit headed bolts and they have a tendency to round off.Hitting them with a hammer loosens the treads and makes them easier to remove.

Tap the disc away from the hub,and this is what your left with.....

Next,the hub face must be cleaned with emery cloth to make sure that it is flat and smooth.If this isn't done,then the new disc will warp causing brake vibration.Once cleaned it should be nice and shiny.

It is now time to fit the new disc.They are covered with an anti-corrosion coating and this needs to be removed before the disc is fitted.A special product is available for this job,but any solvent based product that evaporates will do just as well.Bolt the disc onto the hub using the two bolts removed earlier(recommended tightening torque,15Nm)....

Next,clean the faces of the caliper carrier which the pads touch.This will stop the pads sticking in the carrier.

Next,bolt the carrier back on and tighten the bolts to 100Nm.The pads can then be placed into the carrier.It is a good idea to grease the contact patches between the pad and the carrier,and between the pad and the caliper.This helps prevent the pads sticking in the carrier and also helps to prevent brake squeal.There are special products available to grease the pads,and copper grease should NOT be used!.Also,becareful not to get any of the grease on the disc face or the pad friction face......obviously,the pad friction face goes towards the disc.

Next you have to squeeze the caliper piston back into the caliper.This can be done a number of ways,but I tend to use a large pair of water pump pliers.You have to be gentle when pushing the piston back as it is possible to damage the seals in the master cylinder or the caliper if you try and push it back too fast.This is also why you remove the reservoir cap as the fluid you displace goes back to the reservoir and needs somewhere to overflow if nesseccary.

Once the piston is fully back,you are ready to re-fit the caliper.It's a good idea to grease the sliders before re-fitting the caliper,and make sure they are both free and easy to move.Slide the caliper over the top slider and push the caliper down making sure that the 'see-saw' springs on the pads are against the inner face of the caliper.

Tighten the caliper slider bolt to 35Nm and you are 50% of the way there...

You must now gently pump the brake pedal to bring the piston into contact with the new pads.Push up and down on the pedal slowly,not going beyond half the pedal travel,until the pedal goes solid.

Once you have replaced the other side,do the same and check the fluid level in the reservoir.Adjust the level to get it to the maximum level by removing some of the fluid by either soaking it up with some absorbant paper or using a syringe if you have one.Re-fit the cap,and if any fluid has leaked out,wash off with water.

This is only a guide,and if you are not confident with a set of spanners please don't attempt this job.Your brakes can save your life,so please becareful.If you do have a go at changing your own discs and pads,take your time and double check everything.

After fitting the new discs and pads,avoid heavy braking for at least 200 miles to allow the pads and discs to bed in.

I hope someone finds this usefull,and I will update it again tomorrow as I'm sure I've forgotten a few things........

I need a bit of extra advice ref brakes on alaguna 2 19 dci. i have had new discs and pads fitted all round (Dec09), we had some normals noises comming from the brakes, which i expected as they bedded in. i had my front tyres replaced a week ago since then most of the time when driving the squeeking noiuse are fairly constent and seem to be when i am turning to the left.

is this faulty fitting tyres or discs/pads and can a solve tis my self or will a more technical minded person be neede to help

roo88roo is offline  
Sponsored Links
post #42 of 83 (permalink) Old 28th October 2010
Junior Member
Theram's Avatar
Join Date: Oct 2010
Posts: 10
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 1
Thanked 0 Times in 0 Posts
Re: How to change front discs and pads(with pics)

Lagdti bloody big smiles all round for the detailed information very much appreciated I have done the discs on older cars in the past but was very hesitant in attempting my Mégane.
I hope you do not mind but I have printed this information and pictures for future use
Many thanks again
Currently in Theram's garage:
Renault Megane 2.0 Cab Privillage
Theram is offline  
post #43 of 83 (permalink) Old 1st March 2011
Junior Member
Join Date: Mar 2011
Posts: 2
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 0
Thanked 0 Times in 0 Posts
Talking Re: How to change front discs and pads(with pics)

hey, this was a really useful post. just finnished doing my pads and discs and found that there was no pad actually left and was just a backing plate lol. they made such a noise before, but now quiet as a mouse.

Currently in bendy27's garage:
renault megane coupe 1.6e sport
bendy27 is offline  
post #44 of 83 (permalink) Old 22nd May 2011
Junior Member
Join Date: Feb 2010
Posts: 25
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 3
Thanked 0 Times in 0 Posts
Re: How to change front discs and pads(with pics)

Great post - looked at guide as this is the first time I attempted this job on the laguna and it was very easy job
Currently in Philsha1's garage:
98 laguna estate
Philsha1 is offline  
post #45 of 83 (permalink) Old 15th June 2011
Junior Member
Join Date: Jun 2011
Posts: 11
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 0
Thanked 0 Times in 0 Posts
Re: How to change front discs and pads(with pics)

Don't suppose anyone knows the exact sizes of the four bolts that need removed when doing the brakes.
Did pads and discs the other day and the bolts are in a state so gonna go and buy some new ones and thread-lock them in but need to know the size before I go and buy.
Currently in PolarBear's garage:
2002 meganne 1 1.4 16v fidji
PolarBear is offline  

change , discs , padswith , pics

Quick Reply

Register Now

In order to be able to post messages on the Renault Forums :: Independent Renault forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome