How to change front discs and pads(with pics) - Renault Forums :: Independent Renault forum

Brakes/Hubs Brakes, Hubs, and etc

LinkBack Thread Tools Display Modes
post #1 of 83 (permalink) Old 27th February 2007 Thread Starter
Veteran Member
Technical Supremo
Lagdti's Avatar
Join Date: Dec 2005
Posts: 40,429
Nominated 2 Times in 20 Posts
Nominated TOTW/F/M Award(s): 18
Thanks: 149
Thanked 1,103 Times in 942 Posts
How to change front brake discs and pads

Here is a 'how to' on replacing front brake discs and pads.

I did this on my Laguna 1 phase 2,but the basic principles are the same no matter what car your carrying this out on.

The first thing to do is remove the cap from the brake fluid reservoir.This will save you spraying brake fluid everywhere or damaging the master cylinder.Also,make sure the keys are in the ignition,but with the ignition off.If your car has ABS the pump could be damaged if you have the ignition switched on.

Next,remove the front wheels and put the car on axle stands.Work on one side of the car at a time,and turn the steering to gain easy access to the caliper.

Next,remove the lower caliper bolt.

To do this you will need a 13mm spanner on the bolt and thin headed 17mm open ended spanner to stop the inner slider from spinning.If you haven't got a thin 17mm spanner,then it is possible to use long nose pliers or molegrips.

Once this bolt is removed,pull the caliper up and then slide it off of the top slider.

It's a good idea to support the weight of the caliper by either tying it up to the suspension leg or resting it on top of something so as not to damage the flexible brake hose.

Next,remove the two brake pads......

Next,remove the two 18mm caliper carrier bolts.They will be reasonably tight.....

Once the carrier has been removed,the two disc holding bolts will need to be removed.It is best to hit the heads of them with a hammer before trying to remove them as they are T40 torx bit headed bolts and they have a tendency to round off.Hitting them with a hammer loosens the treads and makes them easier to remove.

Tap the disc away from the hub,and this is what your left with.....

Next,the hub face must be cleaned with emery cloth to make sure that it is flat and smooth.If this isn't done,then the new disc will warp causing brake vibration.Once cleaned it should be nice and shiny.

It is now time to fit the new disc.They are covered with an anti-corrosion coating and this needs to be removed before the disc is fitted.A special product is available for this job,but any solvent based product that evaporates will do just as well.Bolt the disc onto the hub using the two bolts removed earlier(recommended tightening torque,15Nm)....

Next,clean the faces of the caliper carrier which the pads touch.This will stop the pads sticking in the carrier.

Next,bolt the carrier back on and tighten the bolts to 100Nm.The pads can then be placed into the carrier.It is a good idea to grease the contact patches between the pad and the carrier,and between the pad and the caliper.This helps prevent the pads sticking in the carrier and also helps to prevent brake squeal.There are special products available to grease the pads,and copper grease should NOT be used!.Also,becareful not to get any of the grease on the disc face or the pad friction face......obviously,the pad friction face goes towards the disc.

Next you have to squeeze the caliper piston back into the caliper.This can be done a number of ways,but I tend to use a large pair of water pump pliers.You have to be gentle when pushing the piston back as it is possible to damage the seals in the master cylinder or the caliper if you try and push it back too fast.This is also why you remove the reservoir cap as the fluid you displace goes back to the reservoir and needs somewhere to overflow if nesseccary.

Once the piston is fully back,you are ready to re-fit the caliper.It's a good idea to grease the sliders before re-fitting the caliper,and make sure they are both free and easy to move.Slide the caliper over the top slider and push the caliper down making sure that the 'see-saw' springs on the pads are against the inner face of the caliper.

Tighten the caliper slider bolt to 35Nm and you are 50% of the way there...

You must now gently pump the brake pedal to bring the piston into contact with the new pads.Push up and down on the pedal slowly,not going beyond half the pedal travel,until the pedal goes solid.

Once you have replaced the other side,do the same and check the fluid level in the reservoir.Adjust the level to get it to the maximum level by removing some of the fluid by either soaking it up with some absorbant paper or using a syringe if you have one.Re-fit the cap,and if any fluid has leaked out,wash off with water.

This is only a guide,and if you are not confident with a set of spanners please don't attempt this job.Your brakes can save your life,so please becareful.If you do have a go at changing your own discs and pads,take your time and double check everything.

After fitting the new discs and pads,avoid heavy braking for at least 200 miles to allow the pads and discs to bed in.

I hope someone finds this usefull,and I will update it again tomorrow as I'm sure I've forgotten a few things........

I'd rather push my Alfa than drive a BMW....
Currently in Lagdti's garage:
2004 Saab 9-5 HOT Aero and a 2001 Audi A3 1.8 Turbo

Last edited by Lagdti; 27th February 2007 at 09:04 PM.
Lagdti is offline  
The Following 30 Users Say Thank You to Lagdti For This Useful Post:
adiea6 (16th March 2012), basstrom (13th August 2010), benjamindordoigne (19th February 2012), classified (25th February 2013), danzooo (18th August 2013), davef1 (21st September 2011), dingdowner (7th November 2011), dreikaiserbund (21st February 2016), ennessa (2nd May 2011), gerry47 (8th November 2012), GR8GUY (16th March 2012), jimbojim (13th April 2012), Jimrolfe (1st April 2012), kidreflex1 (21st November 2011), lambo28 (28th February 2012), lane4king (18th April 2011), llama_boi626 (12th March 2011), mcjordi (23rd April 2014), mdmajik (8th July 2011), montycaboodle (1st August 2013), pater (11th March 2012), Philsha1 (22nd May 2011), pj1312 (12th August 2012), Proview (19th January 2013), Socrates68 (11th May 2014), talaat_hakim (29th November 2011), Theram (28th October 2010), Widget (6th October 2014), Woodsidemulben (24th July 2013)
  5 Lastest Threads by Lagdti
Thread Forum Last Poster Replies Views Last Post
2014 Isle Of Man TT Bikes Gonescenile 2 2139 2nd June 2014 09:52 PM
40,000th Post......:eek: General Chat excavator 57 5411 3rd May 2013 02:28 PM
Sponsored Links
post #2 of 83 (permalink) Old 28th February 2007
Platinum member
Join Date: Aug 2005
Posts: 14,145
Nominated 2 Times in 3 Posts
Nominated TOTW/F/M Award(s): 3
Thanks: 0
Thanked 68 Times in 26 Posts
Originally Posted by lagdti View Post
Leroy,I know the wheel bearings need swapping over on rear discs on the Clios and 19's,but not 100% sure about your Lag.....

If they are then it's worth spending the extra money and buying new discs with a new wheel bearing and ABS ring already fitted.It is very easy to damage the bearings and the rings when swapping them over.......
Whats the cost difference in the parts, I presume also to fit them in a DIY situation it would be alot quicker as well.



ottoman is offline  
The Following User Says Thank You to ottoman For This Useful Post:
danzooo (1st June 2010)
post #3 of 83 (permalink) Old 28th February 2007
Let's be carefull out there
chris m's Avatar
Join Date: Jan 2006
Posts: 19,344
Nominated 1 Time in 1 Post
Nominated TOTW/F/M Award(s): 3
Thanks: 3
Thanked 32 Times in 32 Posts
Send a message via MSN to chris m
Good post Lag
Currently in chris m's garage:
2000 Scenic 2.0 16v Monaco, BMW 3 Series, Pug 206
chris m is offline  
post #4 of 83 (permalink) Old 28th February 2007
Technical Supremo

Join Date: Feb 2007
Posts: 42,941
Nominated 16 Times in 67 Posts
Nominated TOTW/F/M Award(s): 28
Thanks: 372
Thanked 5,201 Times in 4,712 Posts
Replacing discs and pads

Excellent post Laggy - very well explained. I have done this job numerous times and I would like to add a few extra tips. Winding the caliper piston back in should be done very slowly and gently - ensuring you don't damage the edges or face of the piston. I use an old G-clamp (the type joiners use) and place one of the old pads (lining side against the piston) between the clamp and piston - this ensures the piston is pushed back straight with no risk of the piston being displaced sideways. Gradually turning the screw in the clamp provides enough pressure and prevents damaged knuckles. On cars with ABS and other electronic systems it is best to open the bleeder when retracting the piston - doing it this way minimises any risk to the controls systems. When going this far in replacing pads and discs I would advise the brake fluid be changed. - most car manufacturers recommendations vary - anything from 1-3 years. Vauxhall used to state at least every year. I'll maybe put up a post on this procedure - if asked. Otherwise a truly excellent demo - well done!
Currently in madnoel10's garage:
Honda Civic 1.4l
madnoel10 is offline  
post #5 of 83 (permalink) Old 23rd November 2007
Platinum member
stef123's Avatar
Join Date: Sep 2007
Posts: 2,299
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 50
Thanked 40 Times in 31 Posts
Send a message via MSN to stef123
Hey all,
Just a quick note for anyone else who is trying to decide to do this or not. I have never done this before and let me tell you, it was very very easy!!! took me about 2hours to do both sides - not bad considering the temperatures and it was dark. I would attempt this again anyday!
cheers for all the info,
Currently in stef123's garage:
2006 Ford Mondeo ST TDCI
stef123 is offline  

change , discs , padswith , pics

Quick Reply

Register Now

In order to be able to post messages on the Renault Forums :: Independent Renault forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome