I'm posting this because I couldn't find details anywhere else and someone else may have use for it. I post in good faith. I'm no expert. I may have forgotten something or done something the wrong way. Follow at your own risk etc.
Scenic 2 full dashboard removal to allow heater blower fan replacement.
I can't see how it is possible to replace the fan blower in a Scenic 2 without removing the entire dashboard. There are 2 screws in the top of the housing and the fan must lift out from above.
Picture file names relate to method numbers
Right hand drive Renault Scenic II 2004 model. A/C but no climate control.
2 novices (father and son) making it up as they go along. Took us about 8 hours to remove and replace, but most of the time was spent trying to work out how to remove electrical connectors, and to determine if parts that were reluctant to remove was due to a hidden screw we had missed or a stubborn clip that just needed a firm tug.
There are 3 types of T20 screws, flange head thread into metal, flange head thread into plastic, and round head thread into plastic. I should have counted the screws but I didn't. There was about 20-25 in total
Tools we used: M20 torx with 90 degree ratchet, screwdriver handle & short extension, electric screwdriver, long nose pliers for electrical connectors, small flat screwdriver (for prising off clips) bent coat hanger wire for fishing out lost cables, Gaffa tape. We also used a big clip on LED floodlight. Bright LED torch, electric fan heater on back seat to keep warm. (It's January and pouring with rain and we have no garage) and a good supply of tea and biscuits. I'm bigger than your average slob so I removed the passenger seat half way through to gain more room.
Hardest thing was working out how to release the multitude of different cable connector retainers.
Before starting. Purchase a replacement fan blower, find radio code, disconnect battery,
1. Unclip gear level console cover
2. Remove lower centre console.
3. Remove heater control surround
5. Remove glove box assembly
6. Remove speedo LCD binnacle
7. Remove the steering column covers
8. Remove upper dashboard
9. Remove heater fan
I hope this helps someone. I tried to upload more pics but I don't seem to be able to.
Scenic 2 full dashboard removal to allow heater blower fan replacement.
I can't see how it is possible to replace the fan blower in a Scenic 2 without removing the entire dashboard. There are 2 screws in the top of the housing and the fan must lift out from above.
Picture file names relate to method numbers
Right hand drive Renault Scenic II 2004 model. A/C but no climate control.
2 novices (father and son) making it up as they go along. Took us about 8 hours to remove and replace, but most of the time was spent trying to work out how to remove electrical connectors, and to determine if parts that were reluctant to remove was due to a hidden screw we had missed or a stubborn clip that just needed a firm tug.
There are 3 types of T20 screws, flange head thread into metal, flange head thread into plastic, and round head thread into plastic. I should have counted the screws but I didn't. There was about 20-25 in total
Tools we used: M20 torx with 90 degree ratchet, screwdriver handle & short extension, electric screwdriver, long nose pliers for electrical connectors, small flat screwdriver (for prising off clips) bent coat hanger wire for fishing out lost cables, Gaffa tape. We also used a big clip on LED floodlight. Bright LED torch, electric fan heater on back seat to keep warm. (It's January and pouring with rain and we have no garage) and a good supply of tea and biscuits. I'm bigger than your average slob so I removed the passenger seat half way through to gain more room.
Hardest thing was working out how to release the multitude of different cable connector retainers.
Before starting. Purchase a replacement fan blower, find radio code, disconnect battery,
1. Unclip gear level console cover
a. Unclip gear lever gaiter from bottom (I broke ours). Gaiter and gear knob can remain attached to lever)
b. Prise off console cover
c. Remove switch housing from cover , no need to remove cables.
b. Prise off console cover
c. Remove switch housing from cover , no need to remove cables.
2. Remove lower centre console.
a. 2 screws under radio
b. Remove cigar lighter plug
c. 2 push clips at far end of each foot-well. The spacer box for the passenger side foot-well clip may come loose. Note orientation and position of this spacer box for re-fitting.
d. Console should unclip from the top and drop down
e. Unclip hazard and door lock switch module
f. Remove console
b. Remove cigar lighter plug
c. 2 push clips at far end of each foot-well. The spacer box for the passenger side foot-well clip may come loose. Note orientation and position of this spacer box for re-fitting.
d. Console should unclip from the top and drop down
e. Unclip hazard and door lock switch module
f. Remove console
3. Remove heater control surround
a. Remove 2 screws under radio
b. Lift from bottom and unclip from top
c. Disconnect radio connectors and aerial connector
d. Unclip card reader assembly and detach, note cable routing
e. Disconnect start switch
f. Remove heater control surround
g. Push in 4 side clips to remove radio from heater control surround to assist re-assembly
4. Remove Driver's side lower dashboardb. Lift from bottom and unclip from top
c. Disconnect radio connectors and aerial connector
d. Unclip card reader assembly and detach, note cable routing
e. Disconnect start switch
f. Remove heater control surround
g. Push in 4 side clips to remove radio from heater control surround to assist re-assembly
a. Remove screw at bottom of lower dash above upper door sill foot guard cover.
b. Unclip side cover (air bag switch)
c. Disconnect switch and remove cover
d. Remove screw in side of dash
e. Unclip switch panel and remove wiring plugs (on our model the brown plug was not used.)
f. Remove 2 screws holding handbrake switch, disconnect cable and remove switch assembly
g. Remove screw upper right of handbrake switch location.
h. Remove upper left screw previously hidden behind heater control surround
i. Lower dash can be removed with firm pull against clips along its upper edge.
b. Unclip side cover (air bag switch)
c. Disconnect switch and remove cover
d. Remove screw in side of dash
e. Unclip switch panel and remove wiring plugs (on our model the brown plug was not used.)
f. Remove 2 screws holding handbrake switch, disconnect cable and remove switch assembly
g. Remove screw upper right of handbrake switch location.
h. Remove upper left screw previously hidden behind heater control surround
i. Lower dash can be removed with firm pull against clips along its upper edge.
5. Remove glove box assembly
a. Unclip (but do not try to remove) fuse assembly from drop down fuse lid inside glove box
b. Unclip side panel and remove screws on far left and far right of assembly (mirror positions to driver's side)
c. 2 screws under "roof" inside glove box
d. Remove glove box light and disconnect cable
e. Assembly will unclip from top edge with a firm pull
f. Allow assembly to drop sufficiently to remove 2 connectors behind glove box door switch
g. Remove glove box assembly
h. We also removed the black heater duct running across the foot-well
b. Unclip side panel and remove screws on far left and far right of assembly (mirror positions to driver's side)
c. 2 screws under "roof" inside glove box
d. Remove glove box light and disconnect cable
e. Assembly will unclip from top edge with a firm pull
f. Allow assembly to drop sufficiently to remove 2 connectors behind glove box door switch
g. Remove glove box assembly
h. We also removed the black heater duct running across the foot-well
6. Remove speedo LCD binnacle
a. Unclip and remove upper binnacle trim starting at drivers side and work left
b. Unclip lower binnacle trim likewise
c. Disconnect red connector at top of LCD unit. Push the black tab left ACROSS the top of the red plug
d. Disconnect grey connector at top of LCD unit. Push the black tab left OVER top of grey plug
e. From under the passenger side, disconnect the fan blower cable from the side of the fan, high up centre of passenger foot well. (Thick red and black cable - squeeze in the tabs and pull plug, awkward) try lying upside down on passenger seat with legs around headrest. Whilst under there, disconnect passenger airbag cables and screw in welded metal bracket
f. Pull thick red and black cables and guide fan plug through opening in side of binnacle. Ensure all cables are detached from dashboard and LCD retainers and guides.
g. With hindsight, I suspect it is not absolutely necessary to remove the LCD, but the dashboard is going to get a bit of rough manhandling so I suggest that for this minor step it's probably safer to remove this fragile item.
h. Remove 2 screws in ends of LCD panel
i. From the bottom edge, swing LCD panel assembly up and lift up and out of dashboard. It hangs on plastic studs on each end of assembly
b. Unclip lower binnacle trim likewise
c. Disconnect red connector at top of LCD unit. Push the black tab left ACROSS the top of the red plug
d. Disconnect grey connector at top of LCD unit. Push the black tab left OVER top of grey plug
e. From under the passenger side, disconnect the fan blower cable from the side of the fan, high up centre of passenger foot well. (Thick red and black cable - squeeze in the tabs and pull plug, awkward) try lying upside down on passenger seat with legs around headrest. Whilst under there, disconnect passenger airbag cables and screw in welded metal bracket
f. Pull thick red and black cables and guide fan plug through opening in side of binnacle. Ensure all cables are detached from dashboard and LCD retainers and guides.
g. With hindsight, I suspect it is not absolutely necessary to remove the LCD, but the dashboard is going to get a bit of rough manhandling so I suggest that for this minor step it's probably safer to remove this fragile item.
h. Remove 2 screws in ends of LCD panel
i. From the bottom edge, swing LCD panel assembly up and lift up and out of dashboard. It hangs on plastic studs on each end of assembly
7. Remove the steering column covers
a. Remove 2 screws from under the steering column
b. Release the steering wheel adjuster lock
c. Unclip and remove the top and bottom halves of the column cover
d. Unclip and remove the forward top escutcheon cover. The clips are not captive and are springy. We needed to re-form the springs before re-assembly.
b. Release the steering wheel adjuster lock
c. Unclip and remove the top and bottom halves of the column cover
d. Unclip and remove the forward top escutcheon cover. The clips are not captive and are springy. We needed to re-form the springs before re-assembly.
8. Remove upper dashboard
a. Remove the windscreen pillar covers, firm pull to unclip
b. Remove bottom pillar clip on driver's side
c. Prise off speaker grille on both sides
d. Clip out loudspeakers and disconnect cables (clips face towards the centre line of the windscreen)
e. Disconnect passenger airbag (if not done already -see 6e) NOTE I can't remember if there are 2 or 3 connectors for this and I now have a fault on the airbag yet to be investigated.
f. Remove screw in metal bracket by airbag unit.
g. Remove 2 screws in bottom of radio aperture
h. Remove 4 screws by door pillars left and right (shown removed in photo)
i. Remove 2 screws in ends of heater control unit
j. Release and drop down heater controls by 10-20mm
k. Remove screw in tunnel behind the top of the heat/cool control
l. Try to remember the "feel"; and orientations of the next few stages. It will make re-assembly mush easier. Check there are no more screws (I think I have mentioned them all) Be aware of any connectors that may still be attached or snagged. Pull the entire dashboard away from the windscreen whilst lifting the near edge just far enough for the clips to disengage.
m. This bit is really a 2 person job. Remove the dashboard from the passenger side being careful not to damage the brown connector and cable on the passenger windscreen pillar. You will be glad you removed the driver's side lower pillar clip now.
n. Extract the dashboard through the passenger door. We needed to turn it upside down to do this.
o. Re-assembly is the reverse except for the following
b. Remove bottom pillar clip on driver's side
c. Prise off speaker grille on both sides
d. Clip out loudspeakers and disconnect cables (clips face towards the centre line of the windscreen)
e. Disconnect passenger airbag (if not done already -see 6e) NOTE I can't remember if there are 2 or 3 connectors for this and I now have a fault on the airbag yet to be investigated.
f. Remove screw in metal bracket by airbag unit.
g. Remove 2 screws in bottom of radio aperture
h. Remove 4 screws by door pillars left and right (shown removed in photo)
i. Remove 2 screws in ends of heater control unit
j. Release and drop down heater controls by 10-20mm
k. Remove screw in tunnel behind the top of the heat/cool control
l. Try to remember the "feel"; and orientations of the next few stages. It will make re-assembly mush easier. Check there are no more screws (I think I have mentioned them all) Be aware of any connectors that may still be attached or snagged. Pull the entire dashboard away from the windscreen whilst lifting the near edge just far enough for the clips to disengage.
m. This bit is really a 2 person job. Remove the dashboard from the passenger side being careful not to damage the brown connector and cable on the passenger windscreen pillar. You will be glad you removed the driver's side lower pillar clip now.
n. Extract the dashboard through the passenger door. We needed to turn it upside down to do this.
o. Re-assembly is the reverse except for the following
i. Note in the photo that on a previous "Repair"; of the heater resistor pack the resistor unit was not correctly re-fitted. The forward tab was not engaged under the retainer.
ii. At the time of writing, I am getting a Check airbag, message. And I have a spare yellow/orange connector in the airbag vicinity so I've clearly missed something and will have to disassemble everything again next weekend to find it.
iii. Push the loudspeaker cables through the holes in the dash and prevent them from falling back through before final re-positioning of the dash
iv. Be very careful the loudspeakers don't fall through the holes in the dash when re-assembling.
v. Ensure the heater ducts are aligned before final repositioning of the dash.
vi. Remove the radio from the centre console before refitting (no special tool required)
ii. At the time of writing, I am getting a Check airbag, message. And I have a spare yellow/orange connector in the airbag vicinity so I've clearly missed something and will have to disassemble everything again next weekend to find it.
iii. Push the loudspeaker cables through the holes in the dash and prevent them from falling back through before final re-positioning of the dash
iv. Be very careful the loudspeakers don't fall through the holes in the dash when re-assembling.
v. Ensure the heater ducts are aligned before final repositioning of the dash.
vi. Remove the radio from the centre console before refitting (no special tool required)
9. Remove heater fan
I hope this helps someone. I tried to upload more pics but I don't seem to be able to.