Front Bearing Replacement - Renault Forums :: Independent Renault forum

LinkBack Thread Tools Display Modes
post #1 of 2 (permalink) Old 29th December 2006 Thread Starter
Junior Member
Join Date: Oct 2006
Posts: 3
Nominated 0 Times in 0 Posts
TOTW/F/M Award(s): 0
Thanks: 0
Thanked 0 Times in 0 Posts
Unhappy Front Bearing Replacement

Any details on how to replace the front bearing on a 95 1.2 clio. Any one
Currently in's garage:
1.2 Clio RL Prima is offline  
  5 Lastest Threads by
Thread Forum Last Poster Replies Views Last Post
Front Bearing Replacement Clio chris m 1 2481 29th December 2006 09:23 PM
Hello Peeps Welcome to RenaultForums hondo 5 1067 8th October 2006 06:33 PM
Sponsored Links
post #2 of 2 (permalink) Old 29th December 2006
Let's be carefull out there
chris m's Avatar
Join Date: Jan 2006
Posts: 19,344
Nominated 1 Time in 1 Post
Nominated TOTW/F/M Award(s): 3
Thanks: 3
Thanked 32 Times in 32 Posts
Send a message via MSN to chris m
Hi James. This is not an easy job without the proper tools.

1. apply handbrake, chock rear wheels and jack up appropriate side of car. Remove wheel.

2. refit 2 wheel nuts to the hub & tighten. Remove the driveshaft nut.

3. Unscrew the 2 bolts holding the brake caliper in place, remove caliper from disc and tie to the suspension coil spring to prevent damage to the brake hose.

4. if you have ABS undo the rretaining bolt, withdraw the sensor and tie up as above.

5. Remove the nut securing the track rod end to the swivel hub and release the ball joint (with ball joint separator if needed)

6. remove the nut and clamp bolt securing the lower suspension arm to the swivel hub and carefully lever the joint apart.

7. remove athe 2 nuts securing the swivel hub to the suspension strut. The nuts are positioned at the rear of the strut. Remove bolts and support swivel hub.

8. release driveshaft joint from hub, remove swivel hub assembly. if the splines are a tight fit in the hub use a hammer and soft metal drift or a hub puller to separate.

thats fairly easy and should take about 30 mins.

now the tricky bit.

support the swivel hub on blocks or in a vice.
using a tubular spacer which rests on the inner edge of the hub flange press the flange out of the bearing. if the inner race remains on the hub remove using a bearing puller.

extract the bearing retaining circlip from the inner end of the swivel hub assembly.

using a tubular spacer on the inner race only, press the bearing assembly out of the hub.

clean the hub and remove any burrs.

to refit the bearing (or a new one)

support the swivel hub and locate the bearing in the hub. pres the bearing into the hub using a tubular spacer on the outer race.
NOTE the bearing must enter squarely

fit new circlipand refit hub in reverse to dismantling. remembering to apply locking fluid to the driveshaft splines and any bolt threads.

Note a new driveshaft nut must be used.

finally check the hub spins freely, refit the roadwheel and road test.

from experience the hardest part is separating the bearing from the hub. They are an interference fit so are tight as hell. Add to this several years of grit and muck from the road and they are almost impossible to remove without a hydraulic press. If you know a friendly mechanic, take him the swivel hub and new bearings together with his favourite drink. It's worth at least £20 in time saved.

I have once when desperate resorted to getting a hub with bearings from a breakers for £15 and just swapped the hubs over. Took about an hour all in, then I took the original hub to my local mechanic and had a new bearing fitted ready for the next time.

Good luck.
Currently in chris m's garage:
2000 Scenic 2.0 16v Monaco, BMW 3 Series, Pug 206
chris m is offline  
The Following User Says Thank You to chris m For This Useful Post:
Holborn (18th February 2011)

bearing , replacement

Quick Reply

Register Now

In order to be able to post messages on the Renault Forums :: Independent Renault forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Posting Rules  
You may not post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome