hub

Does anyone know where to get new driveshafts with smaller diameter splines at the hub end? I***8217;ve tried to buy new ones twice using the reg but they all have 28mm diameter which is too big!

Hi, Just about to replace the rear discs on a 2009 2.0 Turbo Laguna III Coupe (petrol) Have already read about and had one panic attack, with reference to electronic parking brake restrictions when compressing calipers. But have just had the wheel off, and the motor is on the rear cross member...

hi can anyone tell me what the rear hub nut torque is on a laguna 2. 2 litre dci 150bhp hatchback is please . have asked around other places and have been told anywhere 100lbs ft to 280lbs ft .

Hey all, Can anyone tell me the toque specs for the following: 1) Caliper Slider Bolts 2) Caliper Bracket Bolts 3) Central Hub Nut I also have a few general questions: 1) Should the bleeder valve be open before pushing the caliper piston back? 2) Are the Brake Rotors held on by the Hub Nut...

Hi guys, does anyone know what the torque setting should be for the scenic 2 litre vvt front hum nuts? Just done a CV joint replacement and can not find the info. Thankyou!

hi all trying to find a front drivers side hub for my 1999 master it's at the slight rumble stage at present i have a garage by me that will try to change the bearing they have a press that goes to 20 tonne but the have sait these are a pig to get out sometimes and sugested i find another hub...

Hey guys, First time posting on here, but have had loads of great help already from the site. Basically, I'm trying to change the front wheel bearings on my Master. I've got everything unscrewed I just can't fathom how to remove the actual hub. The suspension spring is pressing down on the...

Hi I'm new to the website and hopefully have some help. My rear brakes on the offside of my Twingo have jammed on whilst reversing and I'm guessing the rear shoes have binded inside the drum. I need to know the hub size but and what I need to do to unjam the brakes as I think it's going to be...

I have researched this but cannot find an answer so I hope that somebody here may be able to offer some advice. I have a 2002 Kangoo without ABS and I need to change the rear wheel bearing, so I ordered one and set about removing the hub only to discover that the bearing listed is 55mm in...

After reconsidering helicoil repair of stripped wheel bolt hole. Does anyone have any experience of pulling and replacing the front hub drive flange. I`ve already got the brake caliper and wheel disc off. Is it now simply a case of undoing the 30mm drive shaft nut and attaching a hub puller to...

One of the wheel bolt hole threads on my hub have completely stripped. I`ve order M12 x 1.5 tap to try and recut new threads. Also ordered :frown2:a DIY heli-coil kit. Does anyone have any experience of this type of thread repair because I don`t fancy the alternative (ie. replacing the whole...

Having just taken my original plastic wheel covers off to paint the wheels black primarily to stop the advancement of rust after I lost the spare wheel rim to it, I have come to the conclusion I rather like black painted steel wheels and aim to not refit the standard plastic covers as I had a...

As title says N/S/F bearing has went on my Laguna III 2dci 150BHP so intend replacing hub ..looking on Eurocarparts they only seem to list one so presume only one available unless anyone can tell me otherwise ..going to replace discs and pads whilst at it but will take a pad and disc to factors...

Hi all, I'm after shearing off two front wheel bolts on my 2000 kangoo. (My own fault for overtightening with a massive tire iron) I've had no luck trying to drill out the bolts, so my current plan is to wait for it to stop raining, take off the brake rotor and try to get a vise grips on the...

Would anyone like LAGUNA 2 rear hub nuts (77 03 034 275) in unopened packs , free to collector from NORTHAMTON .

im having a bit of difficulty in getting the rear offside wheel hub off my clio dci 03. basically I can't undo the four nuts at the back. They are a weird star shaped nut which at first I thought a 10 mill socket would fit but didn't, so im wondering if i need a specific type of socket or spanner.

Hello chaps, Can anyone confirm if there were two different types of Hub on a 2002 Clio? I won't bore people with why I need to know but it appears the hub's are indentical accept for the size of the hole that the ABS sensor sit's in. Most phase 2's have a wider hole with a wider ABS sensor in...

Hi guys im in the process of fixing an ABS light fault on my clio. I think a bit of rust got onto the sensor. Thought it would be a simple job of taking the wheel hub off so I can get to the cable which is attached to the bearing. Now my only problem is that this things stuck on quite hard. Im...

Hi I am just trying to clarify which way the clio ABS functions so any input would be appreciated the problem; at high speeed i.e. >60mph after 2-7mins (the fast the lower the time required) the ABS trips and no longer functions hopefully its just a matter of replacing a reluctor ring, or...

Hi I wonder if you can help, I have a cracked abs rear on my drivers side rear wheel. I believe I need a whole new rear hub bearing and am trying to find out if I can get an after market one? if not what would your opinion be to fitting a second hand one from a breakers yard? Thanks guys :d